Methods to Change Door Locks

Are you moving to a new house? Maybe you have a new roomie or could only be for safety purposes? Knowing how to change your door locks is indispensable. It isn’t as difficult as we thought! Keep reading to know the step by step procedure to change door locks!

How to Change a Knob Lock

Grab a Phillips head screwdriver. Use this to remove the screws on the inside knob plate. Pull each side’s doorknob away from the door.

In case your knob has no screws on it, the use of a wire tool or a simple paper clip would be necessary. Use the paper clip to release the knob latch by inserting it into the doorknob’s small hole that you can see on its side. Now, you can pull off the knob.

Measuring the diameter of the lock’s hole as well as the distance from its center to the door’s edge is the next step after you have removed the knobs. Make sure to purchase the same brand of your current lock. Also, buy a new lock that matches the measurement of your current lock. This way, you can install your new lock in the existing holes. It will most likely fit the hole’s dimensions.

You can purchase locks online, home improvement stores, hardware stores, or at your nearest locksmith shops.

Next, loosen the two screws holding the latch plate. Once the screws are removed that hold the latch at the edge of the door, you can easily slide it out.

Your purchased new lock comes with a cardboard template. The cardboard template will show you how the lock will fit the door. Enclose this at the door edge. When you are placing the cardboard template over the door’s hole, make sure that all match up. If not match, you purchased the wrong lock.

After your cardboard template matches up, put the new latch into the opening at the edge of your door. Drive and tighten the screws. Make sure you are using new screws because reusing the old ones is not ideal as they are old and maybe weaker.

Finally, it’s time to place the knobs by sliding them through the lock hole toward each other. The outside knob is the one with the keyhole, put it on its respective side. On the other is the inside knob. Slide them through the lock hole toward each other, meeting in the middle and finally connect. Allow the knobs to slide and connect easily. Put the lock back together by driving the screws into the holes on the inside doorknob place.

Change Door Locks: How to Rekey a Lock

You can do rekeying using a kit tagged for its brand if in case you love your existing knobs. This way, you will also do not have to replace the entire lockset.

Always make sure to check your lock’s brand, and then you can buy a kit labeled for it. Rekeying kits work for its specific brand and usually do not work for other locks, so purchasing a rekeying kit that matches your lock’s brand is necessary. You can purchase a rekeying kit online, home improvement stores, hardware stores, or at your nearest locksmith shops.

The next step you need to do is to remove the exterior doorknob by using a wire-like tool that comes with your purchased rekeying kit. Alternatively, you can use a pin to remove the knobs. Unlock the door by inserting your key. Then put the pin into the hole that you can see on the side of the interior doorknob. Now you can pull the outside knob.

In case your lock doesn’t have a small hole, it is best just to replace the whole lock because rekeying will be much complicated for you to do and better off just hiring a locksmith to do it professionally.

Search inside the knob for any plastic sheets or metal that put the lock cylinder in place after you have removed the exterior lock. Slide the plastic sheets or metal, and then put pressure on the key that you inserted into the keyhole in the previous steps. This will allow you to pop the cylinder out of the back of the knob.

Next is you will see a retainer ring that holds or secure the cylinder housing. Grab the wrench-like tool from your rekeying kit. The next step is to slide the tool around the ring and carefully turn the tool to pop the cylinder retainer ring off.

Refer to your rekeying kit again and look for a tube-shaped tool or a cylinder follower. Use the tool to push it through the cylinder housing from the side, which is the opposite of the keyhole. This will allow you to pop the cylinder plug out of the housing.

Make sure to put steady pressure, and the plug and tool are always in contact as you slide the cylinder plug out so that the springs and lock pins do not scatter or fly everywhere.

You will see pins on your cylinder plug. Remove them. Refer to your kit the instructions on how to remove your cylinder plugs old pins.

After removing the old pins from your cylinder plug, put in your new key into the keyhole. You can find the key in the kit. It will also come with numbered or colored pins as well as code instructions. Insert the pins into its corresponding plug slots to match the code in the instructions. When the pins are correctly installed, you will notice that they flush with the plug’s surface and not sticking out over their respective slots.

Shove the cylinder plug back into its housing after installing all the pins. Next is slide the retainer ring back into its place then pop the cylinder into the doorknob. Put back metal or plastic sheets that will hold and secure the cylinder.

Finally, reassemble the exterior doorknob by pushing it into its place in the lock and then carefully rotate the key until the knob locks into place.

Change Door Locks: How to Replace a Deadbolt

Worry no more if your knob lock is in excellent condition, but your deadbolt needs to be changed because replacing a deadbolt is way more relaxed compared to switching out your doorknobs! The following are steps to replace a deadbolt.

First, you have to remove the screws on the inside plate. Next is to remove the deadbolt’s interior faceplate out by pulling it or rotating counterclockwise. Make sure to hold on the exterior faceplate when removing the interior because it might fall on the floor since some models do not screw it into place. Then remove the outer plate by pulling or twisting it.

Remove the screws fastening the set plate and bolt to the edge of the door. Drive the screws and then pull out the set plate and bolt. Finally, you are done uninstalling your old deadbolt.

Now that you disassembled your old deadbolt, pop out the cylinder housing from the outer faceplate, and then you have to rekey it just like how you would rekey a knob lock that we learned previously on this blog. In case you lost the key, a locksmith can help you make a new key. You just have to bring the parts to the locksmith.

Now it is time to assemble the new deadbolt’s set plate and bolt! In case you are changing the entire lock, make sure to begin by inserting the bolt into the hole at the edge of the door where your old bolt fits. But if your plate and bolt are two separate components, put the new set plate over the cut on the side of the door where your old plate is located.

Secure the new lock by screwing through the set plate to the door. Make sure the screws you are using are new, and it would be best if they match your lock’s color.

To complete your new deadbolt‘s installation, attach the new faceplates, both interior, and exterior, on their respective sides and holes in the door. Drive the screws through the holes in the internal plate, through the holes in the bolt, and into the exterior plate until they are tightly attached.

There you have it! Now you already learn how to change door locks, depending on the type of lock you are using. Apply these steps if you are trying to change the door locks yourself!

Don’t have time to do it yourself?

Locksmith Near Me has mobile locksmiths available now to install, repair, rekey or upgrade your door locks. For immediate service or to schedule locksmith service, give us a call now at (844) 234-5400.

How to install a door deadbolt

How to Install a Door Deadbolt

How to Install a Deadbolt: Door Handle Install Part 2/2

Installation of a Deadbolt

Video transcript of the video showing how install a door deadbolt:

How to Install a Deadbolt: Door Handle Install Part 2/2

"What we have here is an entry-level set and a deadbolt. We have the lever set with a thumb turn and lock. This will obviously go on the outside, this will go on the inside, and locking deadbolt inside and outside. Single-sided so it only takes a key on one side. And we're going to install it in this practice door.

OK, so now we're going to install the deadbolt. Most of them are indicated with a stamp on it telling it which side goes up so that the actuator aligns with where the tail piece is from the deadbolt. This one tells us this side is up. So we'll insert that into the opening. We can see that centered. Depending upon how deep the hole is in the door a lot of these are adjustable. So if that's an adjustable one and you see this is crowded over a little bit you'll want to expand it. If it hits the wood here then it probably needs to be shortened. This one's already preset for the right size. And of course the locking part goes on the outside.

What we're going to do is we know that when the key is turned we want the deadbolt to come this direction. Typically the top of the key way moves in the direction that you want the bolt to go, so in this is instance we want to turn this tail piece as far toward the unlocked position as we can. This is wider than it is tall or taller than it is wide in either case we know it has to go into the actuator with this orientation. So we'll turn it all the way this way and then just back far enough to come through that slot. And we'll take our thumb turn and we'll align it with that actuator. And install the screws."

Watch part 1 of this video to see how to install the door lever handleset.

Need help to help install a door deadbolt? Locksmith Near Me has mobile locksmiths available now to install, repair, rekey or upgrade your door locks. For immediate service or to schedule locksmith service, give us a call now at (844) 234-5400.

How to install a door lever handle

How to Install a Door Lever Handle

Installation of a Door Lever Handle

Video transcript of the video How to Install a Lever Door Handle: Part 1/2:

"What we have here is an entry-level set and a deadbolt. We have the lever set with a thumb turn and lock. This will obviously go on the outside, this will go on the inside and locking deadbolt inside and outside. Single-sided so it only takes a key on one side. And we're going to install it in the practice door.

This is the latch. In this instance we're going to install this as though it's a right-handed door so the door is going to close that way. So this obviously needs to go in this direction so that the door is prevented from opening by this latch on the flat side. So that will go in first. We fasten the latch into the door using the two screws provided.

Now with this half moon shape, in this particular brand, that's going to go inside, this is our lock it lockable side, that's going to go on the outside and this has to match up with the same shape there. And in order to insert that we need to push that slightly inward. Slide it in and then the two fasteners match there.

Then we install the lever. And again, that has a matching half moon on this side to match up with this side and then the little white knob in the center is going to be inserted into this tail piece. And as you can see this is designed with a with a space here that covers the screw hole, so rather than fighting this we're just going to take this off with the provided allen wrench. Take this off for now out of our way. We're going to line this up to where this half moon and that button line up with the tail piece and this actuator here. And now we're going to install the lever and tighten it down with the allen wrench."

Watch part 2 of this video to see installation of the door deadbolt.

Need help to install a door lever handle? Locksmith Near Me locksmiths are available 24 hours a day for lock installation, repairs and rekeys for residential and commercial door lock service and maintenance. Call us now at (844) 234-5400.

How to install a garage door slide lock

How to Install a Garage Door Slide Lock

Garage Door Slide Lock Installation

Video transcript of the video How to Install a Garage Door Slide Lock:

"Here we have a couple of common style deadbolts for roll up garage doors. They both function essentially the same in that the latch slides through a hole that is in the rail that the garage door rolls up on, and then you can attach a padlock to secure that so that even if someone pulls the emergency release cord or somehow opens or has access to roll up the door, this physically blocks the door from being able to be rolled up.

The difference between these two is one has levers to actuate it and unlock it, and that can be attached to a cable mechanism or a t-handle on the outside of the garage door that's lockable. This one is simply manually operated both directions to engage or disengage the lock.

These holes have been pre-drilled and I'm also confirming that there's enough room for the bolt to pass through the rail and that there's enough room for the deadbolt to go on. So now we're just going to fasten this in place. Confirm that it works and then we're going to attach an ABUS padlock 83 series that's rekeyable, to a Schlage in this instance, or a Kwikset so that the padlock matches the house key.

Now that's secure. So even if the lock is bypassed or the garage door opener is decoded, this physically prevents the door from being able to roll up. The other feature of this is if someone gains entry to the home by breaking a window or compromising another door, this prevents them from being able to roll up the garage door and haul big stuff out. They have to exit the home the same way they came in."

Click here to watch a video demonstrating how to rekey an ABUS padlock.

Want help installing a garage door slide lock or need the locks on your garage door repaired or rekeyed? Locksmith Near Me is available 24 hours a day for garage door lock repair and garage door maintenance and repair. Call now (844) 234-5400.

Door Handle Install, Lock Repair and Rekey

Installation of New Door Handle & Lock Hardware

Locksmith Near Me in Tucson provides fast and professional service for the installation, service and repair of door handles, knobs and locks for home and business. Our mobile locksmith technicians can professionally repair and rekey the locks and deadbolts on your home or upgrade your home security to the latest home security technology with keyless entry systems that use keypads and Bluetooth technology that enables you to control and manage your home locks and security remotely.

For businesses we can service, replace or upgrade your emergency door exits, install high-security locks, rekey existing office locks and create master key systems for your entire building.

Home Door Lock Handle Install

All the different doors in your home require different kinds of levers and knobs with their own specific locking options. From outdoor hardware that can have keyed handlesets, keypads and deadbolts to indoor bedroom and bathroom knobs that can be either keyed or have a push or turn button for locking.

Along with the myriad of different door knobs, levers and locks to choose from also comes the expertise and tools to install them properly. Wood doors and metal doors may require different tools. From drills and chisels to measuring tapes to power screw drivers. The correct tool and knowledge is required for a professional installation.

Door knob handle install Tucson

Door handle and lock installation

Residential Locks

  • Deadbolts
  • Door knobs
  • Lever handles
  • Handlesets
  • Kyepads
  • Connected devices
  • Touchscreen locks
  • Bluetooth-enables locks
  • Child proof locks
  • Gate locks
  • Mailbox locks
  • Cabinet locks
  • Garage locks
  • Bedroom locks
  • Bathroom locks

Commercial Locks

  • Keyless entry
  • Magnetic locks
  • Restricted key systems
  • Door closers
  • Master key system
  • Exit devices
  • Emergency exit locks
  • Push-bar handle locks
  • Crash-bar door handles
  • Cam locks
  • Mortise locks
  • Rim locks
  • Interchangeable core cylinders
  • Furniture locks

Best Lock Brands

  • Schlage
  • Kwikset
  • Baldwin
  • Yale
  • Mul-T-Lock
  • Medeco
  • Master Lock
  • Corbin Russwin
  • Arrow
  • Sargent
  • Kaba Ilco
  • Chubb
  • Weiser Lock
  • LiftMaster
  • ASSA
Residential Locksmith Near Me

Door Handle & Door Lock Installation & Repair

Home Door Lock Handle Install

All the different doors in your home require different kinds of levers and knobs with their own specific locking options. From outdoor hardware that can have keyed handlesets, keypads and deadbolts to indoor bedroom and bathroom knobs that can be either keyed or have a push or turn button for locking.

Read More

Professional Locksmith Technicians

Locksmith Near Me LLC Now Offering Service in Tucson, Arizona

Locksmith Near Me LLC, a mobile locksmith services company, is now providing automotive, residential and commercial lock & key service in the Greater Tucson area.

TUCSON, Ariz. – Dec. 21, 2016 – Locksmith Near Me LLC, a mobile locksmith company based out of Mesa, Arizona, has announced they have expanded their locksmith service area and have now started offering mobile locksmith service in Tucson, Arizona. The company, which started offering automotive, residential and commercial locksmith services in the Greater Metro Phoenix area in November has rapidly expanded their service area through partnership agreements with experienced independent technicians in Tucson.

Read More